[Olsr-dev] OLSRv2 configuration and wlan

[Henning Rogge]

Can you just post the raw output of "iwconfig wlan1" and "ip addr"?

Getting no interface address on wlan1 is very strange, you should at
least have an IPv6 linklocal address!

Henning Rogge

On Tue, Nov 12, 2013 at 5:56 PM, Karoly Szabo <(spam-protected)> wrote:
> Hi,
> the ip remains the same:
> eth0: 147.162.97.20
> wlan1:  192.168.1.120
> lo: 127.0.0.1
>
> also the result for
> nhdp iflink:
>
> Interface 'eth0': hello_interval=2   hello_vtime=20
>     Address: 147.162.97.20
>     Address: fe80::218:8bff:fe1b:7e59
>     Link: status=symmetric localif=eth0 vtime=38.756   heard=18.756
> symmetric=18.656   dualstack
>         Originator: 147.162.97.9
>         Link addresses: 147.162.97.9
>     Link: status=symmetric localif=eth0 vtime=38.756   heard=18.756
> symmetric=18.656   dualstack
>         Link addresses: fe80::f24d:a2ff:fe37:cbd8
>
> Interface 'lo': hello_interval=2   hello_vtime=20
> Interface 'wlan1': hello_interval=2   hello_vtime=20
>
> Similar results came from the machine with ip: 147.162.97.9
>
> It seems that the Wifi interfaces does not initialize themselves in Olsr.
>
> Regards,
> Karoly
>
>
>
> 2013/11/6 Henning Rogge <(spam-protected)>
>>
>> Hi,
>>
>> what IP addresses have you set on eth0, wlan1 and lo before (and
>> after) you run olsrd2 ?
>>
>> maybe you can run "ip addr" twice, once before you start the routing
>> daemon and once 30 seconds afterwards.
>>
>> Henning Rogge
>>
>> On Wed, Nov 6, 2013 at 7:56 PM, Karoly Szabo <(spam-protected)>
>> wrote:
>> > Hi all, I swapped from version 1 to version 2.
>> > I found some information about the configuration file and i wandered if
>> > exist a complete
>> > list of all the parameters that is possible to set.
>> >
>> > Also I have a problem regarding to Wifi devices, after launching:
>> > olsrd wlan1 eth0 lo
>> >
>> > In telnet I tried to obtain information about all the interfaces
>> > and I'm missing all wlan informations except default hello interval and
>> > vtime (currently connected and pingning a tablet).
>> >> nhdp interface
>> > Interface 'eth0': hello_interval=2   hello_vtime=20
>> >     Address: 147.162.97.20
>> >     Address: fe80::218:8bff:fe1b:7e59
>> > Interface 'lo': hello_interval=2   hello_vtime=20
>> > Interface 'wlan1': hello_interval=2   hello_vtime=20
>> >
>> >> Connection closed by foreign host.
>> >
>> > the routes command also show me all the eth0 nodes but no one from
>> > wlan1.
>> > Somebody had similar problems? Or am I missing something?
>> >
>> > Thanks in advance,
>> > Karoly Szabo
>> >
>> > --
>> > Olsr-dev mailing list
>> > (spam-protected)
>> > https://lists.olsr.org/mailman/listinfo/olsr-dev
>>
>>
>>
>> --
>> We began as wanderers, and we are wanderers still. We have lingered
>> long enough on the shores of the cosmic ocean. We are ready at last to
>> set sail for the stars - Carl Sagan
>
>



-- 
We began as wanderers, and we are wanderers still. We have lingered
long enough on the shores of the cosmic ocean. We are ready at last to
set sail for the stars - Carl Sagan