[Olsr-users] OLSR 0.6.6-2 configuration
Theodoros Bourchas
(spam-protected)
Fri Nov 7 16:44:40 CET 2014
I have used "olsrd -d 9 -f /var/etc/olsrd.conf -nofork" but the issue still
persists.
Should I enable sth in the conf file or do I miss any plugin?
Thanks in advance,
Theodoros
On Fri, Nov 7, 2014 at 4:29 PM, Ferry Huberts <(spam-protected)> wrote:
> use '-nofork' as a cli option, then olsrd will not fork
>
> and 2/3/etc : the higher the more output
>
> On 07/11/14 16:28, Theodoros Bourchas wrote:
>
>> What I get in syslog (syslog-ng installed and tail -f /var/log/messages)
>> is the following and nothing else.
>> In the meantime, the nodes are discovered.
>>
>> Oct 19 16:14:55 Arduino olsrd[22547]: Writing '1' (was 1) to
>> /proc/sys/net/ipv4/ip_forward
>> Oct 19 16:14:55 Arduino olsrd[22547]: Writing '0' (was 1) to
>> /proc/sys/net/ipv4/conf/all/send_redirects
>> Oct 19 16:14:55 Arduino olsrd[22547]: Writing '0' (was 0) to
>> /proc/sys/net/ipv4/conf/all/rp_filter
>> Oct 19 16:14:55 Arduino olsrd[22547]: Writing '0' (was 1) to
>> /proc/sys/net/ipv4/conf/wlan0/send_redirects
>> Oct 19 16:14:55 Arduino olsrd[22547]: Writing '0' (was 0) to
>> /proc/sys/net/ipv4/conf/wlan0/rp_filter
>> Oct 19 16:14:55 Arduino olsrd[22547]: Adding interface wlan0
>> Oct 19 16:14:55 Arduino olsrd[22547]: New main address: 10.0.0.11
>> Oct 19 16:14:55 Arduino olsrd[22547]: olsr.org <http://olsr.org> -
>> 0.6.6-git_508ca62-hash_aa1d94e660f73196451ccb9a42668911 successfully
>> started
>>
>>
>> I also tried with "olsrd -d 2 -f /var/etc/olsrd.conf -nofork" but the
>> issue still persists.
>>
>> Theodoros
>>
>>
>> On Fri, Nov 7, 2014 at 4:05 PM, Ferry Huberts <(spam-protected)
>> <mailto:(spam-protected)>> wrote:
>>
>> olsrd forks into the background, that is why you don't see anything
>> more on the console.
>>
>> look in the syslog after the fork
>>
>> On 07/11/14 15:53, Theodoros Bourchas wrote:
>>
>> Hello olsr community,
>>
>> I have an Arduino Yun board and I want to use OLSR for my project.
>> Arduino Yun comes with Olsr 0.6.6-2 version. After enabling olsr
>> and the
>> related packages (olsrd-mod-* and luci-app-olsr-*)in make
>> menuconfig, I
>> built them and I installed them in the Arduino Yun with kernel
>> 3.3.8.
>> I configured the parameters under /etc/config/olsrd file and I
>> launch
>> the daemon with /etc/init.d/olsrd start.
>> It works, but my issue comes when I have to post some debug
>> output in
>> the console with the routing table of olsrd.
>> When I ran olsrd -f /tmp/etc/olsrd.conf -d 2 , I receive the
>> following:
>> (spam-protected):~# olsrd -d 2 -f /tmp/etc/olsrd.conf
>>
>> *** olsr.org <http://olsr.org> <http://olsr.org> -
>>
>> 0.6.6-git_35ec602-hash___d548b7e0803fe367d1084e4d6a21ce__09
>> ***
>>
>> Build date: 2014-10-14 10:57:11 on debian
>> http://www.olsr.org
>>
>> Parsing file: "/tmp/etc/olsrd.conf"
>> Debug level: 0
>> Noint set to 1
>> IpVersion: 4
>> FIBMetric: flat
>> Link quality level 2
>> LQ Algorithm: etx_ff
>> OlsrPort: 698
>> Willingness: 3
>> NAT threshold 1.00
>> Plugin: olsrd_arprefresh.so.0.1
>> Plugin: olsrd_dyn_gw.so.0.5
>> Plugin: olsrd_httpinfo.so.0.1
>> Plugin param key:"Net" val: "0.0.0.0 0.0.0.0"
>> Plugin param key:"port" val: "1978"
>> Plugin: olsrd_txtinfo.so.0.1
>> Plugin param key:"accept" val: "0.0.0.0"
>> Mode: mesh
>> HELLO validity: 10000000.00
>> TC validity: 1000000.00
>> HELLO interval: 60.00
>> TC interval: 60.00
>>
>> Interface Defaultssetting ifs_in_curr_cfg = 0
>> Mode: mesh
>> HELLO validity: 100000.00
>> TC validity: 100000.00
>> MID interval: 60.00
>> MID validity: 100000.00
>> HNA interval: 60.00
>> HNA validity: 100000.00
>> HELLO interval: 60.00
>> TC interval: 60.00
>> IPv4 broadcast/multicast : AUTO (d)
>> Mode : mesh (d)
>> IPv6 multicast : ff02::6d
>> HELLO emission/validity : 60.00/10000000.00
>> TC emission/validity : 60.00/1000000.00
>> MID emission/validity : 5.00/300.00
>> HNA emission/validity : 5.00/300.00
>> Autodetect changes : yes
>> IPv4 broadcast/multicast : AUTO
>> Mode : mesh (d)
>> IPv6 multicast : ::
>> HELLO emission/validity : 60.00/100000.00
>> TC emission/validity : 60.00/100000.00
>> MID emission/validity : 60.00/100000.00
>> HNA emission/validity : 60.00/100000.00
>> Autodetect changes : no
>> *** olsrd configuration ***
>> Debug Level : 2
>> IpVersion : 4
>> No interfaces : ALLOWED
>> TOS : 0xc0
>> OlsrPort : 698
>> RtTable : 254
>> RtTableDefault : 254
>> RtTableTunnel : 254
>> Willingness : 3
>> IPC connections : 0
>> Pollrate : 0.05
>> NIC ChangPollrate: 2.50
>> TC redundancy : 2
>> MPR coverage : 7
>> LQ level : 2
>> LQ fish eye : 1
>> LQ aging factor : 0.050000
>> LQ algorithm name: etx_ff
>> NAT threshold : 1.000000
>> Clear screen : yes
>> Use niit : yes
>> Smart Gateway : no
>> SmGw. Del Srv Tun: no
>> SmGw. Use Count : 1
>> SmGw. Takedown% : 25
>> SmGw. Pol. Script: (null)
>> SmGw. Egress I/Fs:
>> SmGw. Mark Egress: 91
>> SmGw. Mark Tunnel: 101
>> SmGw. Allow NAT : yes
>> SmGw. period : 10000
>> SmGw. stablecount: 6
>> SmGw. threshold : 0%
>> Smart Gw. Uplink : both
>> SmGw. Uplink NAT : yes
>> Smart Gw. speed : 128 kbit/s up, 1024 kbit/s down
>> # Smart Gw. prefix : ::/0
>> InterfaceDefaults:
>> IPv4 broadcast/multicast : AUTO
>> Mode : mesh
>> IPv6 multicast : ff02::6d
>> HELLO emission/validity : 60.00/10000000.00
>> TC emission/validity : 60.00/1000000.00
>> MID emission/validity : 5.00/300.00
>> HNA emission/validity : 5.00/300.00
>> Autodetect changes : yes
>> dev: "wlan0"
>> IPv4 broadcast/multicast : AUTO (d)
>> Mode : mesh
>> IPv6 multicast : ff02::6d (d)
>> HELLO emission/validity : 60.00/100000.00
>> TC emission/validity : 60.00/100000.00
>> MID emission/validity : 60.00/100000.00
>> HNA emission/validity : 60.00/100000.00
>> Autodetect changes : yes (d)
>> Plugins:
>> Name: "olsrd_txtinfo.so.0.1"
>> Name: "olsrd_httpinfo.so.0.1"
>> Name: "olsrd_dyn_gw.so.0.5"
>> Name: "olsrd_arprefresh.so.0.1"
>> Not using hysteresis
>> OLSRD txtinfo plugin 0.1 by Lorenz Schori
>> Httpinfo olsrd plugin 0.1 by Andreas Tonnesen
>> OLSRD dynamic gateway plugin 0.4 by Various artists
>> Group 0:
>> HNA 0.0.0.0
>> OLSRD arprefresh plugin by Sven-Ola
>> *** olsr.org <http://olsr.org> <http://olsr.org> -
>>
>> 0.6.6-git_35ec602-hash___d548b7e0803fe367d1084e4d6a21ce__09
>>
>> (2014-10-14
>> 10:57:11 on debian) ***
>>
>>
>> and then nothing appears, despite the fact that packets are
>> transferred
>> and neighbors are discovered.
>> Can you help me with this debug output problem?
>>
>> I attach the /tmp/etc/olsr.conf file
>>
>>
>> DebugLevel 0
>> AllowNoInt yes
>> IpVersion 4
>> FIBMetric "flat"
>> LinkQualityLevel 2
>> LinkQualityAlgorithm "etx_ff"
>> OlsrPort 698
>> Willingness 3
>> NatThreshold 1.0
>>
>> LoadPlugin "olsrd_arprefresh.so.0.1"
>> {
>> }
>>
>> LoadPlugin "olsrd_dyn_gw.so.0.5"
>> {
>> }
>>
>> LoadPlugin "olsrd_httpinfo.so.0.1"
>> {
>> PlParam "Net" "0.0.0.0 0.0.0.0"
>> PlParam "port" "1978"
>> }
>>
>> LoadPlugin "olsrd_txtinfo.so.0.1"
>> {
>> PlParam "accept" "0.0.0.0"
>> }
>>
>> InterfaceDefaults
>> {
>> Mode "mesh"
>> HelloValidityTime 10000000.0
>> TcValidityTime 1000000.0
>> HelloInterval 60.0
>> TcInterval 60.0
>> }
>>
>> Interface "wlan0"
>> {
>> Mode "mesh"
>> HelloValidityTime 100000.0
>> TcValidityTime 100000.0
>> MidInterval 60.0
>> MidValidityTime 100000.0
>> HnaInterval 60.0
>> HnaValidityTime 100000.0
>> HelloInterval 60.0
>> TcInterval 60.0
>> }
>>
>> Thanks in advance,
>> Theodoros
>>
>>
>>
>>
>> --
>> Ferry Huberts
>>
>>
>>
> --
> Ferry Huberts
>
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.olsr.org/pipermail/olsr-users/attachments/20141107/86281bef/attachment.html>
More information about the Olsr-users
mailing list