[Olsr-users] OLSR 0.6.6-2 configuration
Ferry Huberts
(spam-protected)
Fri Nov 7 16:29:56 CET 2014
use '-nofork' as a cli option, then olsrd will not fork
and 2/3/etc : the higher the more output
On 07/11/14 16:28, Theodoros Bourchas wrote:
> What I get in syslog (syslog-ng installed and tail -f /var/log/messages)
> is the following and nothing else.
> In the meantime, the nodes are discovered.
>
> Oct 19 16:14:55 Arduino olsrd[22547]: Writing '1' (was 1) to
> /proc/sys/net/ipv4/ip_forward
> Oct 19 16:14:55 Arduino olsrd[22547]: Writing '0' (was 1) to
> /proc/sys/net/ipv4/conf/all/send_redirects
> Oct 19 16:14:55 Arduino olsrd[22547]: Writing '0' (was 0) to
> /proc/sys/net/ipv4/conf/all/rp_filter
> Oct 19 16:14:55 Arduino olsrd[22547]: Writing '0' (was 1) to
> /proc/sys/net/ipv4/conf/wlan0/send_redirects
> Oct 19 16:14:55 Arduino olsrd[22547]: Writing '0' (was 0) to
> /proc/sys/net/ipv4/conf/wlan0/rp_filter
> Oct 19 16:14:55 Arduino olsrd[22547]: Adding interface wlan0
> Oct 19 16:14:55 Arduino olsrd[22547]: New main address: 10.0.0.11
> Oct 19 16:14:55 Arduino olsrd[22547]: olsr.org <http://olsr.org> -
> 0.6.6-git_508ca62-hash_aa1d94e660f73196451ccb9a42668911 successfully
> started
>
>
> I also tried with "olsrd -d 2 -f /var/etc/olsrd.conf -nofork" but the
> issue still persists.
>
> Theodoros
>
>
> On Fri, Nov 7, 2014 at 4:05 PM, Ferry Huberts <(spam-protected)
> <mailto:(spam-protected)>> wrote:
>
> olsrd forks into the background, that is why you don't see anything
> more on the console.
>
> look in the syslog after the fork
>
> On 07/11/14 15:53, Theodoros Bourchas wrote:
>
> Hello olsr community,
>
> I have an Arduino Yun board and I want to use OLSR for my project.
> Arduino Yun comes with Olsr 0.6.6-2 version. After enabling olsr
> and the
> related packages (olsrd-mod-* and luci-app-olsr-*)in make
> menuconfig, I
> built them and I installed them in the Arduino Yun with kernel
> 3.3.8.
> I configured the parameters under /etc/config/olsrd file and I
> launch
> the daemon with /etc/init.d/olsrd start.
> It works, but my issue comes when I have to post some debug
> output in
> the console with the routing table of olsrd.
> When I ran olsrd -f /tmp/etc/olsrd.conf -d 2 , I receive the
> following:
> (spam-protected):~# olsrd -d 2 -f /tmp/etc/olsrd.conf
>
> *** olsr.org <http://olsr.org> <http://olsr.org> -
>
> 0.6.6-git_35ec602-hash___d548b7e0803fe367d1084e4d6a21ce__09 ***
> Build date: 2014-10-14 10:57:11 on debian
> http://www.olsr.org
>
> Parsing file: "/tmp/etc/olsrd.conf"
> Debug level: 0
> Noint set to 1
> IpVersion: 4
> FIBMetric: flat
> Link quality level 2
> LQ Algorithm: etx_ff
> OlsrPort: 698
> Willingness: 3
> NAT threshold 1.00
> Plugin: olsrd_arprefresh.so.0.1
> Plugin: olsrd_dyn_gw.so.0.5
> Plugin: olsrd_httpinfo.so.0.1
> Plugin param key:"Net" val: "0.0.0.0 0.0.0.0"
> Plugin param key:"port" val: "1978"
> Plugin: olsrd_txtinfo.so.0.1
> Plugin param key:"accept" val: "0.0.0.0"
> Mode: mesh
> HELLO validity: 10000000.00
> TC validity: 1000000.00
> HELLO interval: 60.00
> TC interval: 60.00
>
> Interface Defaultssetting ifs_in_curr_cfg = 0
> Mode: mesh
> HELLO validity: 100000.00
> TC validity: 100000.00
> MID interval: 60.00
> MID validity: 100000.00
> HNA interval: 60.00
> HNA validity: 100000.00
> HELLO interval: 60.00
> TC interval: 60.00
> IPv4 broadcast/multicast : AUTO (d)
> Mode : mesh (d)
> IPv6 multicast : ff02::6d
> HELLO emission/validity : 60.00/10000000.00
> TC emission/validity : 60.00/1000000.00
> MID emission/validity : 5.00/300.00
> HNA emission/validity : 5.00/300.00
> Autodetect changes : yes
> IPv4 broadcast/multicast : AUTO
> Mode : mesh (d)
> IPv6 multicast : ::
> HELLO emission/validity : 60.00/100000.00
> TC emission/validity : 60.00/100000.00
> MID emission/validity : 60.00/100000.00
> HNA emission/validity : 60.00/100000.00
> Autodetect changes : no
> *** olsrd configuration ***
> Debug Level : 2
> IpVersion : 4
> No interfaces : ALLOWED
> TOS : 0xc0
> OlsrPort : 698
> RtTable : 254
> RtTableDefault : 254
> RtTableTunnel : 254
> Willingness : 3
> IPC connections : 0
> Pollrate : 0.05
> NIC ChangPollrate: 2.50
> TC redundancy : 2
> MPR coverage : 7
> LQ level : 2
> LQ fish eye : 1
> LQ aging factor : 0.050000
> LQ algorithm name: etx_ff
> NAT threshold : 1.000000
> Clear screen : yes
> Use niit : yes
> Smart Gateway : no
> SmGw. Del Srv Tun: no
> SmGw. Use Count : 1
> SmGw. Takedown% : 25
> SmGw. Pol. Script: (null)
> SmGw. Egress I/Fs:
> SmGw. Mark Egress: 91
> SmGw. Mark Tunnel: 101
> SmGw. Allow NAT : yes
> SmGw. period : 10000
> SmGw. stablecount: 6
> SmGw. threshold : 0%
> Smart Gw. Uplink : both
> SmGw. Uplink NAT : yes
> Smart Gw. speed : 128 kbit/s up, 1024 kbit/s down
> # Smart Gw. prefix : ::/0
> InterfaceDefaults:
> IPv4 broadcast/multicast : AUTO
> Mode : mesh
> IPv6 multicast : ff02::6d
> HELLO emission/validity : 60.00/10000000.00
> TC emission/validity : 60.00/1000000.00
> MID emission/validity : 5.00/300.00
> HNA emission/validity : 5.00/300.00
> Autodetect changes : yes
> dev: "wlan0"
> IPv4 broadcast/multicast : AUTO (d)
> Mode : mesh
> IPv6 multicast : ff02::6d (d)
> HELLO emission/validity : 60.00/100000.00
> TC emission/validity : 60.00/100000.00
> MID emission/validity : 60.00/100000.00
> HNA emission/validity : 60.00/100000.00
> Autodetect changes : yes (d)
> Plugins:
> Name: "olsrd_txtinfo.so.0.1"
> Name: "olsrd_httpinfo.so.0.1"
> Name: "olsrd_dyn_gw.so.0.5"
> Name: "olsrd_arprefresh.so.0.1"
> Not using hysteresis
> OLSRD txtinfo plugin 0.1 by Lorenz Schori
> Httpinfo olsrd plugin 0.1 by Andreas Tonnesen
> OLSRD dynamic gateway plugin 0.4 by Various artists
> Group 0:
> HNA 0.0.0.0
> OLSRD arprefresh plugin by Sven-Ola
> *** olsr.org <http://olsr.org> <http://olsr.org> -
>
> 0.6.6-git_35ec602-hash___d548b7e0803fe367d1084e4d6a21ce__09
> (2014-10-14
> 10:57:11 on debian) ***
>
>
> and then nothing appears, despite the fact that packets are
> transferred
> and neighbors are discovered.
> Can you help me with this debug output problem?
>
> I attach the /tmp/etc/olsr.conf file
>
>
> DebugLevel 0
> AllowNoInt yes
> IpVersion 4
> FIBMetric "flat"
> LinkQualityLevel 2
> LinkQualityAlgorithm "etx_ff"
> OlsrPort 698
> Willingness 3
> NatThreshold 1.0
>
> LoadPlugin "olsrd_arprefresh.so.0.1"
> {
> }
>
> LoadPlugin "olsrd_dyn_gw.so.0.5"
> {
> }
>
> LoadPlugin "olsrd_httpinfo.so.0.1"
> {
> PlParam "Net" "0.0.0.0 0.0.0.0"
> PlParam "port" "1978"
> }
>
> LoadPlugin "olsrd_txtinfo.so.0.1"
> {
> PlParam "accept" "0.0.0.0"
> }
>
> InterfaceDefaults
> {
> Mode "mesh"
> HelloValidityTime 10000000.0
> TcValidityTime 1000000.0
> HelloInterval 60.0
> TcInterval 60.0
> }
>
> Interface "wlan0"
> {
> Mode "mesh"
> HelloValidityTime 100000.0
> TcValidityTime 100000.0
> MidInterval 60.0
> MidValidityTime 100000.0
> HnaInterval 60.0
> HnaValidityTime 100000.0
> HelloInterval 60.0
> TcInterval 60.0
> }
>
> Thanks in advance,
> Theodoros
>
>
>
>
> --
> Ferry Huberts
>
>
--
Ferry Huberts
More information about the Olsr-users
mailing list