[Olsr-users] 3 node setup with media player demo

[(spam-protected)]

Thnaks a lot for help..
I will keep posting the progress of our setup and experiments..

Vijai 

-----Original Message-----
From: Michael Rack [mailto:(spam-protected)] 
Sent: Wednesday, August 19, 2009 4:33 PM
To: Vijai Kumar (WT01 - Joint CEO Office)
Cc: (spam-protected)
Subject: Re: [Olsr-users] 3 node setup with media player demo

Hi,

one mail describes an 3 hop setup. (no alternate path is available) a
other mail describes an 5 hop setup. (there is an alternate path
available).

Thats all ;-)

Michael.

Am 19.08.2009 12:07, schrieb (spam-protected):
> Thanks Michael....
> What do you mean by fallback-route?
> Do you mean alternate path in case of PC2 fails?
>
> -----Original Message-----
> From: Michael Rack [mailto:(spam-protected)]
> Sent: Wednesday, August 19, 2009 1:22 PM
> To: Vijai Kumar (WT01 - Joint CEO Office)
> Cc: (spam-protected)
> Subject: Re: [Olsr-users] 3 node setup with media player demo
>
> OLSR is a transparent Routing-Protocoll, so you dont have to make you 
> worry about the routing. You can reach each PC by the ip-address. So 
> run a Network-Block-Device on PC3 and mount it on PC1 (Use NFS, Samba,

> NBD or what ever).
>
> Install OLSR on all your network connected machines. Bring all 
> machines to the same subnet eg. 172.16.10.0/24. Configure olsrd.conf 
> to use all your installed NICs.
>
> If you like to try to stream a video, then adjust your TTL-Settings 
> for HelloInterval and HelloValidityTime. To make your Network resist 
> to an networkfailure you have to set the following values:
>
>       Interface "eth0" "eth1"
>       {
>           HelloInterval      0.1
>           HelloValidityTime  0.3
>       }
>
> This gives you an fallback-route in 0.3 sec.
>
> Dont forget: In your setup PC1<---->PC2<---->PC3 you dont have any 
> fallback-route!
>
> Michael.
>
> Am 19.08.2009 06:33, schrieb (spam-protected):
>    
>> Hi,
>>
>> I have to setup the simple 3 node setup.
>>
>> PC1<------>PC2<------>PC3
>>
>> I have the olsrd (olsrd-0.5.6-r5) running at above 3 Linux PCs.
>>
>> Question:
>> 1. How can I make the stup such that
>>      one video/audio file is in PC3 disk. I want to start the media 
>> player at PC1 which shuld make connection to PC3 via PC2 (intemediate
>>      
> node).
>    
>>      Is this possible to do If Yes then how.
>> 2. Do I need any other S/W or tool at any other node.
>>
>> Please.... Can anybody explain me this..........;)
>>
>>
>> Thanks to all in advance.
>>
>>
>> Regards
>> Vijai kumar
>> Technical Architect
>> Wipro Technologies
>> India.
>>
>> Please do not print this email unless it is absolutely necessary.
>>
>> The information contained in this electronic message and any
>>      
> attachments to this message are intended for the exclusive use of the
> addressee(s) and may contain proprietary, confidential or privileged 
> information. If you are not the intended recipient, you should not 
> disseminate, distribute or copy this e-mail. Please notify the sender 
> immediately and destroy all copies of this message and any
attachments.
>    
>> WARNING: Computer viruses can be transmitted via email. The recipient
>>      
> should check this email and any attachments for the presence of
viruses.
> The company accepts no liability for any damage caused by any virus 
> transmitted by this email.
>    
>> www.wipro.com
>>
>>
>>      
>
> Please do not print this email unless it is absolutely necessary.
>
> The information contained in this electronic message and any
attachments to this message are intended for the exclusive use of the
addressee(s) and may contain proprietary, confidential or privileged
information. If you are not the intended recipient, you should not
disseminate, distribute or copy this e-mail. Please notify the sender
immediately and destroy all copies of this message and any attachments.
>
> WARNING: Computer viruses can be transmitted via email. The recipient
should check this email and any attachments for the presence of viruses.
The company accepts no liability for any damage caused by any virus
transmitted by this email.
>
> www.wipro.com
>    


Please do not print this email unless it is absolutely necessary. 

The information contained in this electronic message and any attachments to this message are intended for the exclusive use of the addressee(s) and may contain proprietary, confidential or privileged information. If you are not the intended recipient, you should not disseminate, distribute or copy this e-mail. Please notify the sender immediately and destroy all copies of this message and any attachments. 

WARNING: Computer viruses can be transmitted via email. The recipient should check this email and any attachments for the presence of viruses. The company accepts no liability for any damage caused by any virus transmitted by this email. 

www.wipro.com