#
# OLSR.org routing daemon config file
# This file contains the usual options for an ETX based
# stationary network with fisheye
# (for other options see olsrd.conf.default.full)
#
# Lines starting with a # are discarded
#

#### ATTENTION for IPv6 users ####
# Because of limitations in the parser IPv6 addresses must NOT
# begin with a ":", so please add a "0" as a prefix.

###########################
### Basic configuration ###
###########################
# keep this settings at the beginning of your first configuration file

# Debug level (0-9)
# If set to 0 the daemon runs in the background, unless "NoFork" is set to true
# (Default is 1)

 DebugLevel  0

# IP version to use (4 or 6)
# (Default is 4)

 IpVersion 4

#################################
### OLSRd agent configuration ###
#################################
# this parameters control the settings of the routing agent which are not
# related to the OLSR protocol and it's extensions

# FIBMetric controls the metric value of the host-routes OLSRd sets.
# - "flat" means that the metric value is always 2. This is the preferred value
#   because it helps the linux kernel routing to clean up older routes
# - "correct" use the hopcount as the metric value.
# - "approx" use the hopcount as the metric value too, but does only update the
#   hopcount if the nexthop changes too
# (Default is "flat")

# FIBMetric "flat"

#######################################
### Linux specific OLSRd extensions ###
#######################################
# these parameters are only working on linux at the moment, but might become
# useful on BSD in the future

# SrcIpRoutes tells OLSRd to set the Src flag of host routes to the originator-ip
# of the node. In addition to this an additional localhost device is created
# to make sure the returning traffic can be received.
# (Default is "no")

# SrcIpRoutes no

# Specify the proto tag to be used for routes olsr inserts into kernel
# currently only implemented for linux
# valid values under linux are 1 .. 254
# 1 gets remapped by olsrd to 0 UNSPECIFIED (1 is reserved for ICMP redirects)
# 2 KERNEL routes (not very wise to use)
# 3 BOOT (should in fact not be used by routing daemons)
# 4 STATIC 
# 8 .. 15 various routing daemons (gated, zebra, bird, & co)
# (defaults to 0 which gets replaced by an OS-specific default value
# under linux 3 (BOOT) (for backward compatibility)

# RtProto 0

# Activates (in IPv6 mode) the automatic use of NIIT
# (see README-Olsr-Extensions)
# (default is "yes")

# UseNiit yes

# Activates the smartgateway ipip tunnel feature.
# See README-Olsr-Extensions for a description of smartgateways.
# (default is "no")

# SmartGateway no

# Allows the selection of a smartgateway with NAT (only for IPv4)
# (default is "yes")

# SmartGatewayAllowNAT yes

# Defines what kind of Uplink this node will publish as a
# smartgateway. The existence of the uplink is detected by
# a route to 0.0.0.0/0, ::ffff:0:0/96 and/or 2000::/3.
# possible values are "none", "ipv4", "ipv6", "both"
# (default is "both")

# SmartGatewayUplink "both"

# Specifies if the local ipv4 uplink use NAT
# (default is "yes")

# SmartGatewayUplinkNAT yes

# Specifies the speed of the uplink in kilobit/s.
# First parameter is upstream, second parameter is downstream
# (default is 128/1024)

# SmartGatewaySpeed 128 1024

# Specifies the EXTERNAL ipv6 prefix of the uplink. A prefix
# length of more than 64 is not allowed.
# (default is 0::/0

# SmartGatewayPrefix 0::/0

##############################
### OLSR protocol settings ###
##############################

# HNA (Host network association) allows the OLSR to announce
# additional IPs or IP subnets to the net that are reachable
# through this node.
# Syntax for HNA4 is "network-address    network-mask"
# Syntax for HNA6 is "network-address    prefix-length"
# (default is no HNA)
Hna4
{
# Internet gateway
# 0.0.0.0   0.0.0.0
# specific small networks reachable through this node
# 15.15.0.0 255.255.255.0
}
Hna6
{
# Internet gateway
#   0::                     0
# specific small networks reachable through this node
#   fec0:2200:106:0:0:0:0:0 48
}

################################
### OLSR protocol extensions ###
################################

LinkQualityLevel 2

# Link quality algorithm (only for lq level 2)
# (see README-Olsr-Extensions)
# - "etx_float", a floating point  ETX with exponential aging
# - "etx_fpm", same as ext_float, but with integer arithmetic
# - "etx_ff" (ETX freifunk), an etx variant which use all OLSR
#   traffic (instead of only hellos) for ETX calculation
# - "etx_ffeth", an incompatible variant of etx_ff that allows
#   ethernet links with ETX 0.1.
# (defaults to "etx_ff")

LinkQualityAlgorithm    "etx_ff"
LinkQualityAging	0.05
# Fisheye mechanism for TCs (0 meansoff, 1 means on)
# (default is 1)

LinkQualityFishEye  1


#####################################
### Example plugin configurations ###
#####################################
# Olsrd plugins to load
# This must be the absolute path to the file
# or the loader will use the following scheme:
# - Try the paths in the LD_LIBRARY_PATH 
#   environment variable.
# - The list of libraries cached in /etc/ld.so.cache
# - /lib, followed by /usr/lib
#
# the examples in this list are for linux, so check if the plugin is
# available if you use windows/BSD.
# each plugin should have a README file in it's lib subfolder

LoadPlugin "olsrd_dot_draw.so.0.3"
{
	PlParam "Accept" "127.0.0.1"
}


# LoadPlugin "olsrd_txtinfo.dll"
LoadPlugin "olsrd_txtinfo.so.0.1"
{
    # port number the txtinfo plugin will be listening, default 2006
#   PlParam     "port"   "81"
    # ip address that can access the plugin, use "0.0.0.0"
    # to allow everyone
    PlParam     "Accept"   "127.0.0.1"
}

LoadPlugin "olsrd_httpinfo.so.0.1"
{
    PlParam     "port"   "8080"
    PlParam     "host"   "127.0.0.1"
    PlParam     "host"   "192.168.199.9"    
    PlParam     "Net"    "192.168.199.0 255.255.255.0"
}


#############################################
### OLSRD default interface configuration ###
#############################################
# the default interface section can have the same values as the following
# interface configuration. It will allow you so set common options for all
# interfaces.

InterfaceDefaults {
    # Ip4Broadcast      255.255.255.255
}

######################################
### OLSRd Interfaces configuration ###
######################################
# multiple interfaces can be specified for a single configuration block
# multiple configuration blocks can be specified

# WARNING, don't forget to insert your interface names here !
Interface "ra0"
{
    # Interface Mode is used to prevent unnecessary
    # packet forwarding on switched ethernet interfaces
    # valid Modes are "mesh" and "ether"
    # (default is "mesh")

    # Mode "mesh"
 
    # IPv4 broadcast address for outgoing OLSR packets.
    # One usefull example would be 255.255.255.255
    # The second useful value would be to
    # specify the peer adress of an ptp-tunnel.
    # another name of this parameter is "IPv4Multicast"
    # (default is 0.0.0.0, which triggers the usage of the
    # interface broadcast IP)
    
    # Ip4Broadcast      0.0.0.0

    # IPv6 multicast address
    # (default is FF02::6D, the manet-router linklocal multicast)

    # IPv6Multicast	FF02::6D

    # IPv4 src address for outgoing OLSR packages
    # (default is 0.0.0.0, which triggers usage of the interface IP)

    # IPv4Src 0.0.0.0

    # IPv6 src prefix. OLSRd will choose one of the interface IPs
    # which matches the prefix of this parameter.
    # (default is 0::/0, which triggers the usage
    # of a not-linklocal interface IP)

    # IPv6Src 0::/0
    
    # Emission intervals in seconds.
    # If not defined, Freifunk network defaults are used
    # (default is 2.0/20.0 for Hello and 5.0/300.0 for Tc/Mid/Hna)

    HelloInterval       1.0
    HelloValidityTime  20.0
    TcInterval          5.0
    TcValidityTime    15.0
    MidInterval         5.0
    MidValidityTime   300.0
    HnaInterval         5.0
    HnaValidityTime   300.0
    
    # When multiple links exist between hosts
    # the weight of interface is used to determine
    # the link to use. Normally the weight is
    # automatically calculated by olsrd based
    # on the characteristics of the interface,
    # but here you can specify a fixed value.
    # Olsrd will choose links with the lowest value.
    # Note:
    # Interface weight is used only when LinkQualityLevel is set to 0.
    # For any other value of LinkQualityLevel, the interface ETX
    # value is used instead.
    # Weight 0

    # If a certain route should be preferred 
    # or ignored by the mesh, the Link Quality 
    # value of a node can be multiplied with a factor 
    # entered here. In the example the route 
    # using 192.168.0.1 would rather be ignored.
    # A multiplier of 0.5 will result in a small
    # (bad) LinkQuality value and a high (bad)
    # ETX value.
    # Note:
    # Link quality multiplier is used only when
    # LinkQualityLevel is > 0.

    # example 1: reduce LQ to 192.168.0.1 by half
      LinkQualityMult 192.168.199.8 0.5
    # LinkQualityMult 192.168.199.10 0.1
    # example 2: reduce LQ to all nodes on this interface by 20%
    # LinkQualityMult default 0.8

}
