<div dir="ltr">Of course:<br><div><br>1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN <br> link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00<br> inet <a href="http://127.0.0.1/8">127.0.0.1/8</a> scope host lo<br>
inet6 ::1/128 scope host <br> valid_lft forever preferred_lft forever<br>2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc mq state UP qlen 1000<br> link/ether 00:18:8b:1b:7e:59 brd ff:ff:ff:ff:ff:ff<br>
inet <a href="http://147.162.97.20/24">147.162.97.20/24</a> brd 147.162.97.255 scope global eth0<br> inet6 fe80::218:8bff:fe1b:7e59/64 scope link <br> valid_lft forever preferred_lft forever<br>3: eth1: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc pfifo_fast state DOWN qlen 1000<br>
link/ether 00:50:da:45:4c:d4 brd ff:ff:ff:ff:ff:ff<br>4: wlan1: <NO-CARRIER,BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc mq state DORMANT qlen 1000<br> link/ether 00:1d:7d:49:2b:e9 brd ff:ff:ff:ff:ff:ff<br>
inet <a href="http://192.168.1.220/24">192.168.1.220/24</a> brd 192.168.1.255 scope global wlan1<br> inet6 fe80::21d:7dff:fe49:2be9/64 scope link <br> valid_lft forever preferred_lft forever<br><br></div><div>
iwconfig (same cell on the other node of the network):<br><br></div><div>wlan1 IEEE 802.11bg ESSID:"MILCOM2013" <br> Mode:Ad-Hoc Frequency:2.412 GHz Cell: 56:1B:37:92:E2:63 <br> Tx-Power=20 dBm <br>
Retry long limit:7 RTS thr:off Fragment thr:off<br> Encryption key:off<br> Power Management:off<br><br><br></div></div><div class="gmail_extra"><br><br><div class="gmail_quote">2013/11/12 Henning Rogge <span dir="ltr"><<a href="mailto:hrogge@googlemail.com" target="_blank">hrogge@googlemail.com</a>></span><br>
<blockquote class="gmail_quote" style="margin:0 0 0 .8ex;border-left:1px #ccc solid;padding-left:1ex">Can you just post the raw output of "iwconfig wlan1" and "ip addr"?<br>
<br>
Getting no interface address on wlan1 is very strange, you should at<br>
least have an IPv6 linklocal address!<br>
<span class="HOEnZb"><font color="#888888"><br>
Henning Rogge<br>
</font></span><div class="HOEnZb"><div class="h5"><br>
On Tue, Nov 12, 2013 at 5:56 PM, Karoly Szabo <<a href="mailto:szabo.karoly.a@gmail.com">szabo.karoly.a@gmail.com</a>> wrote:<br>
> Hi,<br>
> the ip remains the same:<br>
> eth0: 147.162.97.20<br>
> wlan1: 192.168.1.120<br>
> lo: 127.0.0.1<br>
><br>
> also the result for<br>
> nhdp iflink:<br>
><br>
> Interface 'eth0': hello_interval=2 hello_vtime=20<br>
> Address: 147.162.97.20<br>
> Address: fe80::218:8bff:fe1b:7e59<br>
> Link: status=symmetric localif=eth0 vtime=38.756 heard=18.756<br>
> symmetric=18.656 dualstack<br>
> Originator: 147.162.97.9<br>
> Link addresses: 147.162.97.9<br>
> Link: status=symmetric localif=eth0 vtime=38.756 heard=18.756<br>
> symmetric=18.656 dualstack<br>
> Link addresses: fe80::f24d:a2ff:fe37:cbd8<br>
><br>
> Interface 'lo': hello_interval=2 hello_vtime=20<br>
> Interface 'wlan1': hello_interval=2 hello_vtime=20<br>
><br>
> Similar results came from the machine with ip: 147.162.97.9<br>
><br>
> It seems that the Wifi interfaces does not initialize themselves in Olsr.<br>
><br>
> Regards,<br>
> Karoly<br>
><br>
><br>
><br>
> 2013/11/6 Henning Rogge <<a href="mailto:hrogge@googlemail.com">hrogge@googlemail.com</a>><br>
>><br>
>> Hi,<br>
>><br>
>> what IP addresses have you set on eth0, wlan1 and lo before (and<br>
>> after) you run olsrd2 ?<br>
>><br>
>> maybe you can run "ip addr" twice, once before you start the routing<br>
>> daemon and once 30 seconds afterwards.<br>
>><br>
>> Henning Rogge<br>
>><br>
>> On Wed, Nov 6, 2013 at 7:56 PM, Karoly Szabo <<a href="mailto:szabo.karoly.a@gmail.com">szabo.karoly.a@gmail.com</a>><br>
>> wrote:<br>
>> > Hi all, I swapped from version 1 to version 2.<br>
>> > I found some information about the configuration file and i wandered if<br>
>> > exist a complete<br>
>> > list of all the parameters that is possible to set.<br>
>> ><br>
>> > Also I have a problem regarding to Wifi devices, after launching:<br>
>> > olsrd wlan1 eth0 lo<br>
>> ><br>
>> > In telnet I tried to obtain information about all the interfaces<br>
>> > and I'm missing all wlan informations except default hello interval and<br>
>> > vtime (currently connected and pingning a tablet).<br>
>> >> nhdp interface<br>
>> > Interface 'eth0': hello_interval=2 hello_vtime=20<br>
>> > Address: 147.162.97.20<br>
>> > Address: fe80::218:8bff:fe1b:7e59<br>
>> > Interface 'lo': hello_interval=2 hello_vtime=20<br>
>> > Interface 'wlan1': hello_interval=2 hello_vtime=20<br>
>> ><br>
>> >> Connection closed by foreign host.<br>
>> ><br>
>> > the routes command also show me all the eth0 nodes but no one from<br>
>> > wlan1.<br>
>> > Somebody had similar problems? Or am I missing something?<br>
>> ><br>
>> > Thanks in advance,<br>
>> > Karoly Szabo<br>
>> ><br>
>> > --<br>
>> > Olsr-dev mailing list<br>
>> > <a href="mailto:Olsr-dev@lists.olsr.org">Olsr-dev@lists.olsr.org</a><br>
>> > <a href="https://lists.olsr.org/mailman/listinfo/olsr-dev" target="_blank">https://lists.olsr.org/mailman/listinfo/olsr-dev</a><br>
>><br>
>><br>
>><br>
>> --<br>
>> We began as wanderers, and we are wanderers still. We have lingered<br>
>> long enough on the shores of the cosmic ocean. We are ready at last to<br>
>> set sail for the stars - Carl Sagan<br>
><br>
><br>
<br>
<br>
<br>
--<br>
We began as wanderers, and we are wanderers still. We have lingered<br>
long enough on the shores of the cosmic ocean. We are ready at last to<br>
set sail for the stars - Carl Sagan<br>
</div></div></blockquote></div><br></div>